»óÇ°Ä«Å×°í¸® > ¼¾¼­ > °¡½º/»ê¼Ò/¿¬±â

°¡½º ¼¾¼­ ºê·¹ÀÌÅ©¾Æ¿ôº¸µå
ÆǸŰ¡°Ý : 1,430¿ø (ºÎ°¡¼¼ Æ÷ÇÔ)
»óÇ°ÄÚµå : ZAS-POL-1479-DEL
Á¦Á¶»ç : Pololu
ºê·£µå : Pololu [ºê·£µå¸ô ¹Ù·Î°¡±â]
±¸¸Å¼ö·® : ÀϽÃÇ°ÀýµÈ »óÇ°ÀÔ´Ï´Ù. (ÁÖ¹®: 053-588-4080)
ÃÑ ±Ý¾× :

  • »óÇ°»ó¼¼
  • °ü·Ã»óÇ°
  • ¹è¼Û/±³È¯/¹ÝÇ° ¾È³»
  • »óÇ°¸®ºä
MQ ½Ã¸®ÁîÀÇ °¡½º¼¾¼­µéÀ» º¸´Ù ½±°Ô »ç¿ëÇÒ ¼ö ÀÖ´Â ºê·¹ÀÌÅ©¾Æ¿ô º¸µåÀÔ´Ï´Ù.

0.95" x 0.7"ÀÇ ÀÛÀº »çÀÌÁîÁö¸¸ °íÁ¤¿ë ±¸¸Û, ÀúÇ×À» ¿¬°áÇÒ ¼ö ÀÖ´Â ±¸¸ÛµîÀÌ ³ªÀÖ¾î »ç¿ëÀÌ ¿ëÀÌÇÕ´Ï´Ù.

https://cafe.naver.com/mechawiki/3521



This carrier board is designed to work with any of the MQ-series gas sensors, simplifying the interface from 6 to 3 pins—ground, power and analog voltage output—that are broken out with a 0.1" spacing, making the board compatible with 0.1" headers and standard breadboards and perfboards. This board has two mounting holes and provides convenient pads for mounting the gas sensor¡¯s required sensitivity-setting resistor.

Overview

This breakout board is designed to work with any of the MQ-series gas sensors, simplifying the interface from 6 to 3 pins—ground, +5V VCC, and an analog voltage output—that are broken out with a 0.1" spacing, making the board compatible with 0.1" headersand standard breadboards and perfboards. This board has two mounting holes and provides convenient pads for mounting the gas sensor¡¯s required sensitivity-setting resistor (referred to as RL in the sensor datasheet). All of the board¡¯s traces are on the same side of the PCB, making it easy to see how the pads are connected.

The two mounting holes are intended to be used with #2 screws (not included).

Note that we also offer an alternate gas sensor breakout board that is more compact, with a diameter equal to that of the smaller gas sensor and the broken-out pins beneath the sensor.



¸ÞÄ«¸®¿öÁî






°ßÀû¿äû
±¸¸Å´ëÇà
Äü/¹æ¹®¼ö·É
ÈĺҰáÁ¦
±â¼ú¹®ÀÇ