상품카테고리 > 모듈/전기부품

IOT 개발 보드 ESP8266 / Blynk Board - ESP8266
판매가격 : 46,200
상품코드 :[3755]JOHN
배송일 :당일발송
제조사 :sparkfun
브랜드 :SparkFun [브랜드몰 바로가기]
남은수량 : 2개
구매수량 :
총 금액 :
추가&대량구매 요청 053-588-4080

Blynk보드는 ESP8266 기반의 IOT 개발 보드입니다. 와이파이를 통해 무선통신 프로젝트를 진행할 수 있으며

스파크펀에서 제공하는 예제를 통해 쉽게 사용할 수 있습니다. 온도 습도 센서 / 네오픽셀 RGB LED / I2C  등을 

내장하고 있으며 아두이노를 통해서 프로그래밍할 수도 있습니다. 자세한 내용은 아래의 링크를 참고해주세요.


SparkFun Blynk Board - ESP8266


SparkFun Blynk Board - ESP8266


Description: Blynk is an easy to use app builder that allows users to add a variety of buttons, sliders, graphical displays and even RGB controllers to their phone. The SparkFun Blynk Board is specially designed to work with the ‘widgets’ within the Blynk mobile app to create your next IoT project. Monitor local weather conditions, control LEDs from your phone, even send a tweet when it’s time to water your plants! Every Blynk Board comes fully programmed and also includes a Blynk subscription code card (15k Energy at a $10 value), which will be needed to connect the Blynk Board to your Blynk account, connect to a Wi-Fi signal and you are ready to start Blynking! You’ll be controlling the Blynk Board from half way around the world in no time.

On board every Blynk Board is the economic yet powerful ESP8266 framework that will allow you to connect to most 2.4GHz WiFi networks, that are either open (no password) or protected with WPA, WPA-2, or WEP authentication. The Blynk Board interfaces with the outside world using input/ouput (I/O) “pins” that can either control real-world objects, like motors or LEDs, or read in values from sensors (like light or position). Each of the Blynk Board’s pins are accessible via the large, metal-encircled holes on the edge of the board. These large holes are designed to interface with alligator clip cables – a staple interface cable for beginner and advanced electrical engineer alike. During setup, the RGB LED on the Blynk Board will be your window into its soul. The board uses this multi-colored LED to indicate all sorts of status modes including how to identify which board is yours.

Blynk is a digital dashboard for your iOS or Android device that allows you to easily build graphical interfaces by dragging and dropping widgets to control for your newest IoT projects! With the Blynk app you will be able to control the Blynk board or any other compatible hardware remotely by displaying sensor data, analyzing your surroundings, activating a function of your project and much more.

Are you just getting started with IoT or electronics? Our IoT Starter Kitincludes all the parts to complete the fourteen starting IoT projects.

Note: The Blynk app is compatible with iDevices running iOS 7.0+, and Android’s running any version above or equal to 4.0.

Note: Android is currently supported, however iOS is still being approved by iTunes. We expect it within the next week.

GET STARTED WITH THE BLYNK BOARD GUIDE

BLYNK IOS DOWNLOAD BLYNK ANDROID DOWNLOAD

Features:

  • ESP8266-Based
  • On-Board Si7021 Temp/Humidity sensor
  • Solderless pin connectors - compatible with alligator clips
  • On-Board FTDI for re-programming
  • On-board WS2812 RGB LED
  • General purpose LED and button
  • ADC scaled to 0-3.3V
  • Expansion connectors for I2C and WS2812 output
  • LiPo battery charger
  • Arduino programmable
  • Over a dozen pre-loaded Blynk projects!
  • No programming required to connect the board to Blynk and run through the example projects
  • Blynk Subscription Code-Card Included

Documents:

▶아래 플러스 친구 버튼을 통해 다양한 정보와 교제 자료 및 이벤트등의 소식을 받아보실 수 있습니다.













견적요청
구매대행
퀵/방문수령
후불결제
기술문의