+즐겨찾기    로그인   회원가입    고객센터    
                     

MAX98357A I2S 3W 오디오 앰프 모듈 / Adafruit I2S 3W Class D Amplifier Breakout - MAX98357A
판매가격 : 8,800원 (부가세 포함)
상품코드 :[0454]JOH-ADA-3006
배송일 :당일발송
제조사 :Adafruit
브랜드 :Adafruit [브랜드몰 바로가기]
남은수량 : 10개 이상
구매수량 :
총 금액 :
추가&대량구매 요청 053-588-4080

MAX08537기반의 디지털 오디오 앰프 모듈입니다.  라즈베리파이 등에 사용할 수 있으며, 스피커와 연결하여 컴팩트한

사운드를 구현해줄 수 있습니다.


Listen to this good news - we now have an all in one digital audio amp breakout board that works incredibly well with the Raspberry Pi! If you're looking for an easy and low cost way to get you digital sound files bumpin' then the MAX08357 I2S Amp Breakout is for you. It takes standard I2S digital audio input and, not only decodes it into analog, but also amplifies it directly into a speaker. Perfect for adding compact amplified sound, it takes 2 breakouts (I2S DAC + Amp) and combines them into one.

I2S (not to be confused with I2C) in a digital sound protocol that is used on circuit boards to pass audio data around. Many high end chips and processors manage all of the audio in digital I2S format. Then, to input or output data, three or four pins are used (data in, data out, bit clock and left-right channel select). Usually, for audio devices, there's a DAC chip that will take I2S in and convert it to analog that can drive a headphone.

This small mono amplifier is surprisingly powerful - able to deliver 3.2 Watts of power into a 4 ohm impedance speaker (5V power @ 10% THD). Inside the miniature chip is a class D controller, able to run from 2.7V-5.5VDC. Since the amp is a class D, it's incredibly efficient - making it perfect for portable and battery-powered projects. It has built in thermal and over-current protection but we could barely tell it got hot.

The audio input is I2S standard, you can use 3.3V or 5V logic data. The outputs are "Bridge Tied" - that means they connect directly to the outputs, no connection to ground. The output is a ~300KHz square wave PWM that is then 'averaged out' by the speaker coil - the high frequencies are not heard. All the above means that you can't connect the output into another amplifier, it should drive the speakers directly.

There's a Gain pin that can be manipulated to change the gain. By default, the amp will give you 9dB of gain. By connecting a pullup or pull down resistor, or wiring directly, the Gain pin can be set up to give 3dB, 6dB, 9dB, 12dB or 15dB.

The ShutDown/Mode pin can be used to put the chip in shutdown or set up which I2S audio channel is piped to the speaker. By default, the amp will output (L+R)/2 stereo mix into mono out. By adding a resistor, you can change it to be just left or just right output

Works great with Raspberry Pi, Arduino Zero, and any other microcontroller or microcomputer with I2S audio outputs

Specs:

  • Output Power: 3.2W at 4Ω, 10% THD, 1.8W at 8Ω, 10% THD, with 5V supply
  • PSRR: 77 dB typ @ 1KHz
  • I2S sample rates from 8kHz to 96kHz
  • No MCLK required
  • Click + Pop reduction
  • Five pin-selectable gains: 3dB, 6dB, 9dB, 12dB, 15dB
  • Excellent click-and-pop suppression
  • Thermal shutdown protection

Comes as an assembled and tested breakout board, with a small piece of optional header and 3.5mm terminal block. Some soldering is required to attach the header and terminal block if those are desired.  Check out the tutorial for schematics, diagrams, examples and more!

설명 설명 설명 설명
                    
회사 메카솔루션 | 대표 정동화 | 사업자등록번호 301-31-31899 | 통신판매업신고번호 제2015-대구달서-0699호
반품주소 대구시 달서구 호산동 711 대구벤처공장 B관 322-b호 | 전화번호 053-588-4080
방문수령 (주문 후 수령만 가능) 대구시 달서구 호산동 711 대구벤처공장 B관 223호 | 팩스번호 053-289-5499
메일 buyms4080@gmail.com (구매전 서비스) csms5499@gmail.com (구매후 서비스) techms5499@gmail.com (기술,제품,불량)
Copyright ⓒ www.mechasolution.com All right reserved