¶óÁ¸®ÆÄÀÌ ¿Àµð¿À È®À彯µå / Expansion Shield x400 for Raspberry Pi B+/2B/3B
ÆǸŰ¡°Ý : 52,800¿ø (ºÎ°¡¼¼ Æ÷ÇÔ)
»óÇ°ÄÚµå : [11042]WAD-ZAS-DFR-PTW-DFR0449-DEL
¹è¼ÛÀÏ : ´çÀϹ߼Û
Á¦Á¶»ç : DFRobot
ºê·£µå : DFRobot [ºê·£µå¸ô ¹Ù·Î°¡±â]
³²Àº¼ö·® : 11°³
±¸¸Å¼ö·® :
°³
ÃÑ ±Ý¾× :
Ãß°¡&´ë·®±¸¸Å ¿äû 053-588-4080

  • »óÇ°»ó¼¼
  • °ü·Ã»óÇ°
  • ¹è¼Û/±³È¯/¹ÝÇ° ¾È³»
  • »óÇ°¸®ºä

¶óÁ¸®ÆÄÀÌ ¿Àµð¿À È®Àå ½¯µåÀÔ´Ï´Ù. ¶óÁ¸®ÆÄÀÌ B+, ¶óÁ¸®ÆÄÀÌ2, ¶óÁ¸®ÆÄÀÌ 3¿¡¼­ »ç¿ëÇÒ ¼ö ÀÖ½À´Ï´Ù.


INTRODUCTION

The X400 Expansion Shield is a highly cost-effective audio hat which fits on the GPIO of the Raspberry Pi Model B+, Raspberry Pi 2 Model B and Raspberry Pi 3 Model B. It uses i2S interface audio solution and supports 24-bit /192KHz high quality sound. It is compatible with other audio equipment via RCA lotus socket. It includes a built-in high fidelity headphone amplifier, where you can plug in a 3.5mm audio jack directly.

The shield has two digital amplifier output ports, up to 2 x30w speakers can be directly connected. Use this hat to make your Raspberry Pi in to a lossless audio player or a network radio. We recommend using an OS image such as Volumio, RuneAudio, PiMusicBox etc.


Note: Raspberry Pi is not included in the box.

SPECIFICATION

  • Input Voltage
    • 6V to 24V DC converted to 5V, 3A via step-down DC/DC converter to power the Raspberry Pi 
  • Audio  
    • Full-HD audio
    • up to 24-bit/192kHz playback  
    • Class leading audio; 112db SNR, and THD of 0.0019%  
    • Audiophile TI Burr Brown 32-bit/384kHz DAC (TI PCM5122)
    • Uses the digital I2S audio signals to reduce CPU load over USB audio solutions  
    • Integrated hardware volume control  - Mute can be enabled / disabled via jumper
    • Built in High quality audio headphone amplifier (TI TPA6133A)
    • Earphone AMP can be enabled / disabled via jumper
    • Built in high quality Class-D stereo audio amplifier (TI TPA3118D2)  
    • Up to 2 x 20W into 4 ohm
    • AMP can be enabled/disabled via jumper  
    • Phono/RCA connectors 
    • 3.5mm stereo audio jack
    • Speaker terminals
  • Wireless  
    • Built in IR sensor (38KHz)
  • Misc  
    • Power output socket  
    • DIP switch to remove connection from RPi¡¯s pin header
    • Directly connected on top of the Raspberry Pi using the board GPIO header pins 
    • No wiring or soldering is required 
    • Pin mappings identical to 40-pin header of the R-Pi in order to support existing expansion boards 
    • Suitable for Raspberry Pi Model B+, 2 Model B and 3 Model B
  • Dimensions
    • 85 x 56mm (Same footprint as Raspberry Pi) 

DOCUMENTS

SHIPPING LIST

  • X400 Expansion Board x1
  • Nylon Spacers (M3 x 20mm) x4
  • Nylon Screws (M3 x 6mm) x8
  • Jumper Wires x2

¸ÞÄ«¸®¿öÁî






°ßÀû¿äû
±¸¸Å´ëÇà
Äü/¹æ¹®¼ö·É
ÈĺҰáÁ¦
±â¼ú¹®ÀÇ