상품카테고리 > 센서/감지 > 적외선/거리/근접

GP2Y0D8XXZ0F 거리센서 호환 PCB기판 Pololu Carrier for Sharp GP2Y0D815Z0F, GP2Y0D810Z0F, and GP2Y0D805Z0F Sensors
판매가격 : 2,200원 (부가세 포함)
상품코드 :[1546]JOHN
배송일 :당일발송
제조사 :Pololu
브랜드 :Pololu [브랜드몰 바로가기]
남은수량 : 10개
구매수량 :
총 금액 :
추가&대량구매 요청 053-588-4080

Overview

The GP2Y0D805GP2Y0D810 , and GP2Y0D815 are Sharp’s smallest and fastest distance sensors, and this tiny carrier board for these sensors includes all of the external components required to make them work. With detection distances up to 150 mm and a typical sampling rate of almost 400 Hz, these sensors provides an attractive alternative to shorter-rangeLED-phototransistor reflectance pairs and longer-range but slower sensors such as the Sharp GP2Y0A41SK0F analog distance sensor.

However, these sensors require external components and have a non-standard 1.5 mm pitch, which can make them difficult to integrate into projects based on a 0.1″ pitch. This carrier board includes these components and provides a 0.1″-pitch, three-pin interface: ground, power, and output.

Note: this product requires a Sharp GP2Y0D815Z0FGP2Y0D810Z0F, or GP2Y0D805Z0F sensor (sold separately). We also offer this carrier board assembled with a GP2Y0D815Z0Fassembled with a GP2Y0D810Z0F, and assembled with a GP2Y0D805Z0F.

Using the carrier board

Pololu carrier with Sharp GP2Y0D805Z0F, GP2Y0D810Z0F, or GP2Y0D815Z0F digital distance sensor.

You will need to solder the sensor to the carrier board so that the solder connections are made on the component-side of the board and the sensor package presses against the component-free side of the board. Once the sensor is soldered in, the Pololu carrier board lets you interface with the GP2Y0D815, GP2Y0D810, or GP2Y0D805 sensor using a three-pin 0.1″ connector, such as the included 3×1 straight male header strip and 3×1right-angle male header strip. You can connect to these pins with a servo cable or with a custom-made cable using pre-crimped wires and a 3×1 crimp connector housing.

The square pad is ground, the middle pad is VIN (2.7 – 6.2 V), and the remaining pad is the sensor output, OUT. Depending on your power source, you might notice an increase in performance by placing a large (>10 uF) capacitor between power and ground somewhere near the sensor.

A red LED on the back of the PCB lights when the output is low, indicating that the sensor is detecting something. If so desired, you can disable this LED by cutting the trace between it and the OUT pin where it is marked on the silkscreen or by desoldering the LED.

The GP2Y0D815Z0F, GP2Y0D810Z0F, and GP2Y0D805Z0F have an optional enable input that can be used to put the sensor into low-power mode. The Pololu carrier board connects this input to Vcc so that the sensor is always enabled, but you can solder a wire to the pad labeled “enable” on the back of the PCB if you want control over this input. Note that you will need to cut the trace that connects the enable line to Vcc on the PCB if you want to be able to disable the sensor. This trace is marked on the silkscreen, and there is a caret that indicates where we suggest you make the cut.

The carrier board has a 0.086″ mounting hole for a #2 or M2 screw. You can make the module more compact by cutting or grinding off this portion of the PCB if you do not need the mounting hole.

Pololu carrier for Sharp GP2Y0D805Z0F, GP2Y0D810Z0F, and GP2Y0D815Z0F sensors schematic diagram.

People often buy this product together with:

Sharp GP2Y0D810Z0F Digital Distance Sensor 10cmSharp GP2Y0D810Z0F Digital Distance Sensor 10cm
Sharp GP2Y0D805Z0F Digital Distance Sensor 5cmSharp GP2Y0D805Z0F Digital Distance Sensor 5cm
Pololu Carrier with Sharp GP2Y0D810Z0F Digital Distance Sensor 10cmPololu Carrier with Sharp GP2Y0D810Z0F Digital Distance Sensor 10cm

▶하단의 배너를 클릭하시면 hardwares.kr로 이동됩니다







견적요청
구매대행
퀵/방문수령
후불결제
기술문의